Nano Calcium Remover BOAT is a very effective product for hard-to-remove deposits that cannot be cleaned with commonly available products. It is ideal for preparing various surfaces before applying the nano protections themselves. Its special composition also works in the pores of the cleaned surface and can separate even deeply ingrained dirt, which can then be easily wiped off. The most common applications include limescale on glass, painted parts and Gelcoat, but it can clean rust and oxidized metal and stainless steel surfaces as well. Not abrassive.
Nano Calcium remover BOAT is specifically developed as a non-abrasive extra strong and fast cleaner for heavily soiled surfaces, where impurities form hard silicates that cannot be removed with conventional products. It is used in the cleaning of boats, cladding, interiors and other very difficult to clean surfaces. It removes, cleans, restores and renovates the surface very quickly in a single operation. The product has a very fast reaction, which immediately penetrates into the structure of the sediment and removes it, cleaning it in depth. It is also ideal for use on vertical walls, significantly reduces consumption and increases efficiency of cleaning. After using this product, it is necessary to degrease the surface with PIKATEC Nano Degreaser & Polisher BOAT before further application of a PIKATEC protective polish. We recommend to protect the cleaned surface immediately with the appropriate PIKATEC polish, depending on the type of surface. The protective polishes create an ultra-thin hydrophobic layer with protection against subsequent contamination, oils, grease, reduces the subsequent deposition of coatings and impurities.
- Mineral and salt deposits
- Eliminates and dissolves biological impurities (algae, cyanobacteria, moss, insects, crustaceans)
- Calcium impurities
- Corrosion and light oxidation
- Yellow stains from fiberglass exterior of the ship
This product should be needed only for the first time cleaning and preparation for the first application or for deep cleaning of long time neglected and uncleaned protected surfaces. Otherwise, warm water and if needed PIKATEC Shampoo for boats should suffice for cleaning of protected surfaces. The Clacium remover does not damage the rubber seals.
The product is designed for hand, low pressure washing and machine washing. For best results, spray, leave on for a few minutes and rinse with high pressure, medium pressure or machine. Nano Calcium Remover BOAT replaces mechanical cleaning such as needling, sandblasting, dry ice blasting, sanding, washing with abrasive cleaners that damage the surface.
Package contents and Consumption
The package is sufficient for about 20 m2, the price for 1 m2 is therefore 1,30 EUR. Consumption is stated for the undiluted quantity, in the case of dilution the yield of the package is even greater, up to twice. The bottle contains 200 ml of Nano Calcium Remover BOAT - Calcium and limescale remover. Should you be interested in wholesale purchase, email us please at: firstname.lastname@example.org.
Salt water vs. Fresh water
All PIKATEC Nano BOAT Series products are adapted for extreme and demanding environments of marine conditions (salt water).Therefore, the protection is fully sufficient for fresh water as well. For boats exposed to salt water it is needed to use unambiguously this product ; for fresh water, the standard household Calcium remover may be sufficient. However, whilst using the one specifically designed for boats, you esure it will work properly.
We recommend removing loose dirt from the surface (this will significantly reduce consumption). Use in undiluted form to remove minerals. for other applications dilute up to 1: 2 with clean water. The dilution of the product depends on the thickness and amount of layers to be removed. Always moisten the surface before application. The product is designed for hand, low pressure washing, machine washing. For best results, spray. After application, leave on for a few minutes and rinse (you can also apply high pressure with caution to the surface). Nano Calcium Remover BOAT replaces mechanical cleaning such as needling, sandblasting, dry ice blasting, grinding, washing with abrasive cleaners that damage the surface. Washing and removal of cladding, skeletons and floors.
The duration of action of the product needs to be determined individually for each individual use on the basis of a small area test. Sometimes it is necessary to repeat the cleaning process, especially for extremely clogged areas with minerals. For a specific application, a procedure must be chosen based on the results of a preliminary test on the small area.
The standard way of usage is spraying the surface and subsequent wiping with a microfiber cloth after a certain time. If you are cleaning large areas, it may be more convenient to apply the cleaner with a roller, for example. Always leave on for a while before wiping the surface. The time needs to be determined by a test.
Due to the wide range of surfaces, we recommend performing a test for compatibility with the surface treatment before the actual application. For each surface to be cleaned, test the reaction of the material with the cleaner on a small less wissible area. Continue with cleaning only if no negative reaction occurs. The cleaner´s formulation is really strong to work well, so please take precautions and use it carefully.
Depending on the type of surface to be cleaned, then treat it with Gelcoat Nano Protect Gelcoat BOAT, stainless steel / chrome (Nano Protect Stainless BOAT), which creates a protective nano layer on the surface to prevent further adhesion of dirt, oils, water and grease.
Note: The product is not intended for removing stains deep in the structure of the material (glass, stainless steel, metals, etc.). These are created by the long-term action of limescale and other chemicals, that had already damaged the structure of these surfaces. Surfaces affected in this way can no longer be chemically cleaned, only mechanically cleaned and renovated.
No user reviews so far.
User reviews :
User reviews can be submitted only by registered and logged-in users.