Glasses and mirrors always look elegant, no matter where they are used. However, their maintenance is very demanding. Most often in the bathrooms we solve problems where the water leaves traces on all surfaces very quickly, and if we don´t keep wiping the glass immediately, it leave indelible maps on it. This is due to limescale and daily used chemicals, which react with the glass and etch its structure very quickly. Is that not possible? Try to shine through the glass shower-corner screen with stronger light, and even though it may seem clean at first glance, the light will tell you the opposite.Glass damaged in this way can hardly be cleaned with anything, it gets dirty much more, damage grows and the glass begins to whiten. Less reachible surfaces that cannot be cleaned so often are even much more stressed.Roof windows, solar panels, hard-to-reach areas, there everywhere water acts also, and together with the sun, the process of damaging the glass is even more accelerated.
The Nano Protect Glass protective polish smooths the surface of glass as well as mirror surfaces and creates a flexible, hard layer of nanoparticles of silicon oxide and zirconium. The treatment closes the surface perfectly, then the protected surface gets less dirty and its maintenance is very easy. Thanks to water repellency, water drops roll quickly away from the surface by gravity, and traces of those that remain on the glass can be very easily wiped off at any time. The polish thus protects against limescale and chemicals (such as remains of soaps and shower gels in bathrooms), which act on the surface of the glass, "eat" into its structure and can hardly be removed over the time. Bacteria that used to settle and multiply on the glass have nowhere to adhere to the treated surface. Protected areas are thus naturally antibacterial. Do you want to know more about the technology?
CAUTION: The product can only be polished with the aid of the product Nano Degreaser & Polisher. Always apply to surfaces free of all impurities.
Package contents and consumption
The package contains 140 ml of Nano Protect Glass - Glass protection. It is sufficient for up to 30m2. For final polishing it is necessary to use the product Nano Degreaser & Polisher
Applications of nanocosmetics
Application of the products is not complicated at all. You only need to follow the 4 steps. The surface must be thoroughly cleaned and degreased on the first place. Then apply a protective polish, leave on for 5 minutes and then polish with a cloth. Always read the relevant instructions in the package.
Surface maintenance after application
Surfaces treated with Pikatec nanocosmetics are smoother, much more resistant to damage and for their maintenance just a dry or moistened microfiber cloth is sufficient. With that you will be able to wipe off all dirt easily, the treated surfaces will always look like new and you will not need any other harmful chemicals to clean them. How to clean properly?
Instructions for use
Surface preparation: Before applying, it is necessary to remove all impurities and grease from the glass which could cause a limited function and shorten the service life of the polish. Check if there are no traces of water drops or other stains on the glass or the mirror. These need to be removed before application, otherwise you would "conserve" them in the protective layer and it would be very difficult to get rid of them afterwards. Always perform the final cleaning / degreasing of the glass with the help of the product Nano Degreaser & Polisher - (formerly called Nano Clear Glass), which we spray lightly, at best, on microfibre cloth and rub the glass with it.
Application: Shake the product well before use and also frequently during application. Using a pump, spray only one dose of protective polish on the application cloth or, for larger areas, on the application pad. Using circular movements then apply a continuous and very thin film of the product to the surface. When working, try not to apply the product over the already covered area, as this would increase the laboriousness and difficulty of both application and subsequent polishing. You don't have to worry - we're in a nano environment and one layer (one swipe on the surface with an application cloth) is perfectly sufficient for surface treatment. After covering the whole area, let the polish harden for 5 minutes. After 5 minutes, start polishing the surface with a microfibre cloth, lightly sprayed with the Nano Degreaser & Polisher. Do not press too hard on the cloth - if you start to feel the more effort is needed than before, add little amount of the Degreaser & Polisher on the cloth and continue working. As the cloth absorbs excess polish, it is advisable to keep folding it and turning it at the time it starts to leave smudges on the polished surface.
One week to two weeks after application, it is necessary to wash the glass by hand with warm water and after drying it should be cleaned with a cloth, on which we can lightly spray again the Nano Degreaser & Polisher. This removes remaining grease which the protective polish additionally eliminated from the glass (so-called emulsifiers) and which loweres the water-repellent effect until fully removed.
- The protective polish cannot be removed from the surface by common cleaning chemicals. If the water-repellent properties are locally reduced, for example when greasing the surface, or by covering the nanolayer with soap residues, etc., the glass must be thoroughly washed with warm water and, if necessary, the affected area degreased. The water-repellent effect is then renewed again.
- The protective polish is not suitable for sandblasted and otherwise surface-treated glass.
- The nanolayer does not prevent water condensation on the glass.
- Use the polish immediately after opening the bottle.
Types of hazards: Flammable liquids with possible eye damage, skin irritation, respiration hazard and specific target body organs toxicity.
No user reviews so far.
User reviews :
User reviews can be submitted only by registered and logged-in users.